Pasivni zujalica za Arduino koja s PWM-om proizvodi ton i prikladna je za 4 V do 8 V.
SKU: OT2071-D125 Broj artikla: AB012 EAN: 4308851007787 Lokacija: D12.05
Alternativa
Aktivni modul zujalice
€ 1,40
Pogledaj ovu alternativu
Ovako spoji Pasivni buzzer modul za Arduino na Arduino UNO ili ESP32, uz primjer sketcha koji možeš odmah učitati.
Ovaj projekt pokazuje kako generirati glazbene tonove s pasivnim buzzer modulom pomoću Arduino Uno. Arduino šalje signale promjenjive frekvencije putem funkcije tone() kako bi reproducirao glazbenu ljestvicu. Otvorite Serial Monitor na 115200 baud kako biste vidjeli frekvencije koje se trenutačno reproduciraju.
/*
* ==================================================================
* Generated by Codey.online — https://www.codey.online
* ==================================================================
* Project : Passive Buzzer Melody Player
* Board : Arduino UNO (arduino:avr:uno)
* Parts : Buzzer module passief Arduino
* Libraries : none (built-in)
*
* Codey Online is an AI-powered browser IDE for Arduino and ESP32.
* Describe your project and Codey writes the code, draws the wiring
* diagram and uploads it to your board, straight from the browser.
* This code is free to use, modify and share, without warranty.
* ==================================================================
*/
// Passive Buzzer Module Demo on Arduino Uno
const int BUZZER_PIN = 9;
// Musical notes in Hertz (C major scale: C4 to C5)
const int notes[] = {262, 294, 330, 349, 392, 440, 494, 523};
const int noteCount = sizeof(notes) / sizeof(notes[0]);
void setup() {
Serial.begin(115200);
Serial.println(F("Passive Buzzer Demo Starting..."));
}
void loop() {
Serial.println(F("Playing scale ascending..."));
for (int i = 0; i < noteCount; i++) {
Serial.print(F("Tone: "));
Serial.print(notes[i]);
Serial.println(F(" Hz"));
tone(BUZZER_PIN, notes[i], 150);
delay(200);
}
delay(300);
Serial.println(F("Playing scale descending..."));
for (int i = noteCount - 1; i >= 0; i--) {
tone(BUZZER_PIN, notes[i], 150);
delay(200);
}
noTone(BUZZER_PIN);
delay(1500);
}
Wiring diagram and example code generated by Codey.online — https://www.codey.online
Ovaj primjer pokazuje kako generirati glazbene tonove pomoću pasivnog buzzer module uz ESP32. Mikrokontroler koristi PWM tone generation za višekratno reproduciranje niza glazbenih nota. Spojite buzzer module izravno na napajanje, masu i GPIO pin kako biste čuli melodiju.
/*
* ==================================================================
* Generated by Codey.online — https://www.codey.online
* ==================================================================
* Project : ESP32 Passive Buzzer Melody Player
* Board : ESP32 DEVKIT V1 (esp32:esp32:esp32doit-devkit-v1)
* Parts : Buzzer module passief Arduino
* Libraries : none (built-in)
*
* Codey Online is an AI-powered browser IDE for Arduino and ESP32.
* Describe your project and Codey writes the code, draws the wiring
* diagram and uploads it to your board, straight from the browser.
* This code is free to use, modify and share, without warranty.
* ==================================================================
*/
// Pin connected to the passive buzzer's PWM input
const int BUZZER_PIN = 25;
// Frequencies in Hz for a simple arpeggio
const int melody[] = {262, 330, 392, 523};
const int noteDurations[] = {250, 250, 250, 400};
void setup() {
Serial.begin(115200);
pinMode(BUZZER_PIN, OUTPUT);
Serial.println("ESP32 Passive Buzzer Demo Started!");
}
void loop() {
Serial.println("Playing melody...");
for (int i = 0; i < 4; i++) {
tone(BUZZER_PIN, melody[i], noteDurations[i]);
delay(noteDurations[i] * 1.30); // Pause between notes
noTone(BUZZER_PIN);
}
delay(2000); // Wait 2 seconds before playing again
}
Wiring diagram and example code generated by Codey.online — https://www.codey.online
Ovaj pasivni buzzer daje ton od približno 85db kada je spojen na napon između 4V i 8V. Za ovaj pasivni buzzer potreban je mikrokontroler kako bi buzzer proizvodio zvuk putem PWM signala. Buzzer troši oko 30mA.
Napon: 5V
Prikladno za npr. Arduino
Dimenzije
Duina: 2,5cm
Širina: 1,5cm
Visina: 1,1cm

| Širina | 1,5 cm |
|---|---|
| Prikladno za | Arduino |
| Duljina | 2,5cm |
| Potrošnja struje | oko 30mA |
| Visina | 1,1 cm |
Još nema recenzija.
Pasivni buzzer modul za Arduino